Sterilizer.com Sterilizer Parts Technical Home FAQ Search Submit a Question Your Local Service Login
Enter question keywords
to search

Submit your question, for a FREE help

Forum Titles on Scican Statim Replies
code 6 : cycle aborted, " not sterile" three times 2
110 V to 240 V transformer 1
240volts to 110Volts 0
a beep sounds when i turn on the statim 2000 0
Acceptable Water 0
Acceptable Water 1
Bilogical filter exploded 2
Boiler 0
Boiler Replacement 0
calibration 1
calibration 0
cassett is coming out wet 1
cassett not sterilized 1
cassette is hard to remove 2
Continuos beeping touch buttons will not work 0
cycle defective 28 0
Cycle error 3 2
cycle fault 16 0
cycle fault 16 0
cycle fault 16 0
Cycle fault 19 0
cycle fault code 25 0
cylce fault # 12 2
diagram 1
drainage 0
drying 2
empty reservoir 0
Error #6-Boiler needs recalibration 0
Error 16 0
Error 25 1
Error 25 2
Error 25 0
error 26 1
error 26 1
error code 26- not sterile 3
Generic test sheet for Statim 2000 0
hello i have error 60 appearing on my statim 0
How to bench test a Statim printer...? 0
I can not change the language and I do all ok 1
manuel 1
model 1102 0
my esterilizer rports error 8 when in in proces of heating 2
My statim shows quality water no good after I refilled regularly with same water every time. 2
NEED TUBING 1
No clicking or holding when I put cassette in 2
no response from push buttons 0
Oil derposits on condensor bottle 0
outside of cassette 1
Owners Manual 0
Parts for Statim 2000 1
Pressure not releasing 0
Pressure not releasing 0
Program does not start 0
Routine Monitoring of STATIM 2000 0
schmatic for statim 1
Scican Statim 2000- cycle fault #25 2
Scican Statim 2000 -error 16 3
SCICAN Statim 2000 error code 11 1
Scican Statim 2000 Sterilizer with empty reservoir bottle 1
Scican Statim 2000 Sterilizer-service and supplier needed in South Africa 0
SCICAN Statim Cycle Interrupted 1
SCICAN Statim Error Code 01 1
SCICAN Statim error code 10 1
SCICAN Statim error code 12 1
SCICAN Statim error code 13 1
SCICAN Statim error code: 14 1
SCICAN Statim error code: 15 1
SCICAN Statim error code: 16 1
SCICAN Statim error code: 17 18 1
SCICAN Statim error code: 19 1
SCICAN Statim error code: 20 1
SCICAN Statim error code: 21, 22, 23, 24 1
SCICAN Statim error code: 25 1
SCICAN Statim error code: 26 1
SCICAN Statim error code: 27 1
SCICAN Statim error code: 3 1
SCICAN Statim error code: 4 1
SCICAN Statim error code: 5 1
SCICAN Statim error code: 6 1
SCICAN Statim error code: 7 1
SCICAN Statim error code: 8 1
SCICAN Statim error code: 9 1
SCICAN Statim GFI (Ground Fault Interrupter) trips when Statim is starting the drying cicle 0
SCICAN Statim GFI (Ground Fault Interrupter) trips when Statim is turned on 1
SCICAN Statim Loud buzzing noise 1
SCICAN Statim makes a clicking noise when the cassette removed 1
SCICAN Statim No display or garbled display on LCD 1
SCICAN Statim No power for PCB ver 2.4-2.9 1
SCICAN Statim No power for PCB ver 3.0 or 4.2 1
SCICAN Statim Noise during drying cycle only 1
SCICAN Statim Press Stop to Reset 1
SCICAN Statim Printer Fault 1
SCICAN Statim Steam is escaping from condenser bottle vent hole 1
SCICAN Statim Steam is leaking from Push-In Fitting at rear of Statim 1
Scican Statim steri bag placement paper side up, or down 0
Scican Statim Sterilizer-calibration 0
SCICAN Statim Touch pads do not work 1
SCICAN Statim Water dripping from drain tube under Statim 1
SCICAN Statim Water Quality is NOT Acceptable 1
SCICAN Statim Wraps remain wet after drying 1
Scican-Statim 2000 new error message and new fault 0
SciCen Statim 2000 calibration 2
Stat IM 2000 Owners Manual 0
Statim 2000 2
Statim 2000 error 1 1
Statim 2000 Error 19 2
Statim 2000 Error 26 1
statim 2000 error service needed 0
Statim 2000 how change the language? 2
Statim 2000 Installing A Juniper 0
Statim 2000 sterilizer cut-off temperature 1
Statim 2000 water is not being acceptable 1
Statim 2000 will not start 0
Statim 2000: Which water to use 1
StatIM 5000 "water quality not acceptable" 1
StatIM 5000 "water quality not acceptable" 0
Statim 5000 calibration 0
Statim 5000 calibration 0
Statim 5000 Cycle error code 02 2
STATIM 5000 cycle fault 1
Statim 5000 Error code 98 0
Statim 5000 turning off beeping 0
Statim 5000 water draining out during cycle 2
Statim 5000, how to stop beeping 0
Statim Buzzz and sometimes loud clicking sound 0
Statim printer testing 0
Statim will not start 0
statim will not start 0
Statim will not start 1
statim,fault # 8 0
Steam escapes from around cassette 0
Steam/mist under LCD dispaly Statim 2000 2
Steam/Mist under Statim 2000 LCD display.... 0
steri bags paper side up, or paper side down??? 0
Sterilizer 0
Test sheet for Statim 2000 0
Thermal Fuse 0
trying to change language ?? 0
UAS OF RACK INSIDE CASETTE 0
UAS OF RACK INSIDE CASETTE 0
used spring water on a statim 0
water quality requirements 1
First Page    The page 1 of 1 pages    Last Page

The technical information is just to help sterilizer users as reference to do their trouble shooting. no guarranty implied. For each specific technical help to do with sterilizers or autoclaves, go to www.sterilizers.com ... or call 1-800-801-9934 E-mail us